Configuration for the srf06-cc26xx platform. More...

#include <stdint.h>
#include "board.h"

Macros
Network Stack Configuration
#define	NETSTACK_CONF_NETWORK sicslowpan_driver

#define	NETSTACK_CONF_MAC csma_driver

#define	NETSTACK_CONF_RDC contikimac_driver

#define	NULLRDC_CONF_802154_AUTOACK 1

#define	CONTIKIMAC_CONF_WITH_CONTIKIMAC_HEADER 0

#define	CONTIKIMAC_CONF_WITH_PHASE_OPTIMIZATION 0

#define	WITH_FAST_SLEEP 1

#define	NETSTACK_CONF_RDC_CHANNEL_CHECK_RATE 8

#define	NETSTACK_CONF_FRAMER framer_802154

#define	NETSTACK_CONF_RADIO ieee_mode_driver

#define	RF_CORE_CONF_CHANNEL 25

#define	NULLRDC_CONF_802154_AUTOACK_HW 1

#define	NULLRDC_CONF_SEND_802154_ACK 0

#define	NETSTACK_RADIO_MAX_PAYLOAD_LEN 125

#define	SICSLOWPAN_CONF_COMPRESSION SICSLOWPAN_COMPRESSION_HC06

#define	SICSLOWPAN_CONF_COMPRESSION_THRESHOLD 63

#define	SICSLOWPAN_CONF_FRAG 1

#define	SICSLOWPAN_CONF_MAXAGE 8

IEEE address configuration
Used to generate our RIME & IPv6 address
#define	IEEE_ADDR_CONF_HARDCODED 0
	Location of the IEEE address 0 => Read from InfoPage, 1 => Use a hardcoded address, configured by IEEE_ADDR_CONF_ADDRESS.

#define	IEEE_ADDR_CONF_ADDRESS { 0x00, 0x12, 0x4B, 0x00, 0x89, 0xAB, 0xCD, 0xEF }
	The hardcoded IEEE address to be used when IEEE_ADDR_CONF_HARDCODED is defined as 1.

RF configuration
#define	IEEE802154_CONF_PANID 0xABCD
	Default PAN ID.

#define	IEEE_MODE_CONF_AUTOACK 1
	RF H/W generates ACKs.

#define	IEEE_MODE_CONF_PROMISCOUS 0
	1 to enable promiscous mode

#define	RF_BLE_CONF_ENABLED 0
	0 to disable BLE support

#define	PROP_MODE_CONF_SNIFFER 0
	1 to enable sniffer mode

IPv6, RIME and network buffer configuration
#define	LINKADDR_CONF_SIZE 8

#define	UIP_CONF_LL_802154 1

#define	UIP_CONF_LLH_LEN 0

#define	UIP_CONF_BUFFER_SIZE 1000

#define	UIP_CONF_ROUTER 1

#define	UIP_CONF_ND6_SEND_RA 0

#define	UIP_CONF_IP_FORWARD 0

#define	RPL_CONF_STATS 0

#define	RPL_CONF_OF rpl_mrhof

#define	UIP_CONF_ND6_REACHABLE_TIME 600000

#define	UIP_CONF_ND6_RETRANS_TIMER 10000

#define	NBR_TABLE_CONF_MAX_NEIGHBORS 20

#define	UIP_CONF_MAX_ROUTES 20

#define	UIP_CONF_TCP 1

#define	UIP_CONF_TCP_MSS 64

#define	UIP_CONF_UDP 1

#define	UIP_CONF_UDP_CHECKSUMS 1

#define	UIP_CONF_ICMP6 1

Generic Configuration directives
#define	ENERGEST_CONF_ON 0
	Energest Module.

Character I/O Configuration
#define	CC26XX_UART_CONF_ENABLE 1
	Enable/Disable UART I/O.

#define	CC26XX_UART_CONF_BAUD_RATE 115200
	Default UART0 baud rate.

#define	BOARD_CONF_DEBUGGER_DEVPACK 1

#define	SLIP_BRIDGE_CONF_NO_PUTCHAR 1

#define	SLIP_RADIO_CONF_NO_PUTCHAR 1

Button configurations
Configure a button as power on/off: We use the right button for both boards.
#define	BUTTON_SENSOR_CONF_ENABLE_SHUTDOWN 1

#define	PLATFORM_HAS_BUTTON 1

#define	button_sensor button_left_sensor

#define	button_sensor2 button_right_sensor

Compiler configuration and platform-specific type definitions
Those values are not meant to be modified by the user
#define	CLOCK_CONF_SECOND 128

#define	CCIF

#define	CLIF

#define	CLOCK_LT(a, b) ((signed long)((a) - (b)) < 0)

#define	RTIMER_CLOCK_DIFF(a, b) ((int32_t)((a) - (b)))

typedef uint32_t	clock_time_t

typedef uint32_t	uip_stats_t

typedef uint32_t	rtimer_clock_t

Detailed Description

Configuration for the srf06-cc26xx platform.

Definition in file contiki-conf.h.

Macros

Compiler configuration and platform-specific type definitions

Detailed Description